• Please be sure to read the rules and adhere to them. Some banned members have complained that they are not spammers. But they spammed us. Some even tried to redirect our members to other forums. Duh. Be smart. Read the rules and adhere to them and we will all get along just fine. Cheers. :beer: Link to the rules: https://www.forumsforums.com/threads/forum-rules-info.2974/

1973 Tucker Sno Cat 1443 New to Me

Track Addict

Bronze Member
GOLD Site Supporter
This cat was built as a pontoon cat and converted at the factory to rubber. It's a 1443 but has 5 wheels go figure. Eventually Tucker moved to the Dana's. The 8 3/4 was pretty common on the pontoon cats. Not sure about the rubber ones.
 

Track Addict

Bronze Member
GOLD Site Supporter
Differential is back and rebuilt like new. Mitchell Differential in Shrewsbury MA was a pleasure to work with.

Was all bearing and race wear that allowed the slop. New yoke bearing seals and adjustments. Knowing what I saw here rear is slated next year.

Some fresh paint and back in it goes.
70C7A6CD-6375-497D-9016-2BB46D2E38E0.jpeg
41595A67-36DF-474D-B2EE-F03EE0C323A6.jpeg
7468E054-20E4-4DEC-AB87-E61A7C2E0895.jpeg
63AC7894-D198-47A2-855B-9C09325D6ACD.jpeg
 

Track Addict

Bronze Member
GOLD Site Supporter
Cleaned up the housings in prep for assembly. Here you can see the bearing tape wear. Both inner outer bearing tapes lifted but stayed in place. A tacky glue like substance developed.

Still a cost effective solution. One day the Tucker Sleeve Update Kit is the way to go.

Fresh paint and if I get the time will hit the carriers.

Need a new axle tube seal which is SKF 1900.
E96C2206-3BBA-4728-8530-2A1D072796EE.jpeg
DC0E1737-14DD-4AB2-8FCD-11AF2BA8C874.jpeg
FCA35788-F60F-44E8-A3D0-64603814875C.jpeg
797D373C-D483-49A4-A602-F07066F0DE46.jpeg
 

Track Addict

Bronze Member
GOLD Site Supporter
Testing out a theory which might be covered already. Different attack angles and side hilling allows the diff fluid to run past the axle seals.

The original design was for flat roads. Been inside a few of these and the bearings are always washed out with gear lube. Rears is probably less impacted but going up over sno drifts banks etc the oil leaks out.

So I lowered the level to about 3/4 incline. With such slow diff speed should be non issue. Will prob add some Lucas treatment to thicken sticky as well. Carriers need to come off again for paint so we shall see.

B1C98C65-FD55-4334-9537-409CCC552285.jpeg
F3A75CB6-6217-479A-A6FD-D9ABEA428945.jpeg
 

Track Addict

Bronze Member
GOLD Site Supporter
Here is an example of where the green bearings solve a problem and should work on pontoons. Found a set in the parts that came with it which were larger so maybe someone thought the same.

The early 8 3/4 used shims to extend the retainer outward with a foam sealing gasket. Removing shims reduced end play. Later they added an adjuster to one side to take up the slack. Tucker didn’t have this so started with tucker tolerance.

All the 8 3/4” cats I have had apart they are all recessed with lots of end play. My guess is it’s from years of slopping around.

My solution was to have these shims made up solve the problem.

Axle play on the pontoon cats should move the sprocket and pontoon together. With the rubber track the carrier is fixed so the sprocket can move side to side hitting the carrier which you can see in the pictures.

These didn’t have foam seals. Diagrams don’t show but can’t hurt.


803C0D7E-491D-4F98-9F56-73C238EE519D.jpeg
4B8E48FF-2A3D-477F-88CE-C66AAEBE7ED0.jpeg
07D122CD-ADBC-4251-9813-8F0302B3D003.jpeg
AB590E99-C656-4263-855D-0827F4C311B3.jpeg
B6421B54-7BCE-482E-B253-62854FEC5132.jpeg
A807FBD3-2475-49DA-B5AF-6DFCA4C21B17.jpeg
04FF4C46-E7B3-4A5F-BDF8-0B73CC1C51F6.jpeg
 

Track Addict

Bronze Member
GOLD Site Supporter
Set the axle end play. Needed two of these to get into what I think is spec.

If you have ever installed the carriers on these the studs are loose. Trying some rtv to hold them. You need to bolt on the outer journal to install the carrier then remove the nuts and add the retainer. During this process if not careful you can lose the retaining bolt into the carrier and it has to come off.

Non nyloc work well here. Grade 5 or 8 nylocs for the retainer final torque.


226DF02F-C456-4F56-AEB0-6930D5F3E52A.jpeg
160376A5-4658-4708-B8DF-913FF5CF8EE7.jpeg
C84B7E1F-EFF2-4815-AC2E-2F645A52AABA.jpeg
 

Track Addict

Bronze Member
GOLD Site Supporter
Cleaned up the carriers for new tape and install. Here you can see the wear pattern well on the drivers side not as much on the passenger.

I also think the passenger side was replaced. That one has a snap ring retainer that is not on this model schematic and the other carriers don’t have the groove.

Also less wear in that side in comparison.

This cat came with a legend of the operator on MT Greylock running down the mountain missing a track. Maybe the carrier was damaged beyond repair?

D5517D45-BFC3-49FE-A9B9-A408953C6016.jpeg
6B4C38FA-BAF7-4EA0-81F3-2EED13086BA4.jpeg
 

Track Addict

Bronze Member
GOLD Site Supporter
Carriers back on. Drivers side confirmed more worn. Used the same bearing tape measurements and had to trim and work the passenger side on.

Checked all the bolts front and back frame down.

80E76CDF-CE21-463F-95B0-588C306EF6B1.jpeg
1F2D0920-E850-462C-9344-CE9D7D679649.jpeg
E7453103-06D3-442E-9AC5-441EC98A7E70.jpeg
7DEB92DD-7B65-44C5-A946-13101C7D72C1.jpeg
 

Snowy Rivers

Well-known member
Looking great,

Would be nice to replace that inner track carrier support where the plastic strips are with an easily replaceable UHMW ring.......That would make a "Tune up" a simple task......
 

Track Addict

Bronze Member
GOLD Site Supporter
Bill Cook made one Tucker uses now. It involves removing and rewelding smaller journals on and a Uhmw sleeve.

Think it was 600$ a track decade ago. Tape is cheap and easy for now but one day.
 

Track Addict

Bronze Member
GOLD Site Supporter
Hubs back on. This is an areas to get super tight and check regularly on all Tucker Sno Cats. They can loosen.

Three wheels have bad so will freshen those up. Greased the rest. This cat has mix of idler seals, washers, spacers.

Pricing out the update spacers with orings. May swap over if reasonable.

Trying to figure out this ice breaker setup. Idler shafts is shorter than all the others with a different nut that is recessed. Any input appreciated.

F326CC90-CE32-47AB-8257-5DD2FE0FC869.jpeg
F326CC90-CE32-47AB-8257-5DD2FE0FC869.jpeg
53191AF2-C0E5-4AFC-8CF7-5555C7BEEEE2.jpeg
535185B8-A1B8-44BB-BF27-22AC82101A93.jpeg
C979FFDF-B18A-4B37-A090-2EA278C446D6.jpeg
3A6CBE1A-5ACA-4F48-A04F-9D2AD64F7512.jpeg
22019FE1-A031-40B0-9FE7-FB56BDDF9C41.jpeg
6BA60765-57D5-4352-B04B-A9842C04D6F8.jpeg
 

Track Addict

Bronze Member
GOLD Site Supporter
Spoke with dealer today. That icebreaker spindle is a newer style. If I understood correct it’s shorter, has oring machined on spindle in the back, uses a different nut and cap pictured here. More like a basic trailer bearing setup. Eliminates a seal, spacer, washer, and the need to machine orings in two spacers plus use less material.

Bearings are common A6 found anywhere. Seals little harder. Was also told Tucker installed the seals like any tapered bearing to hold the grease in. Thinking was Bill Cook started reversing them and the lip which let old grease moisture and dirt out and new grease in. The retaining washers followed later most like because the yankee ez lube hub forced seals out with cold grease most likely.

Wicked smart idea!

449E2FE5-D1E8-4E81-A2B3-9D022DBEDAC4.jpeg
6AABC65A-0A7B-4F91-812F-F3BF66081440.jpeg
5A6FBF87-D1CF-47D8-9E49-0E1FA5BA7FEC.jpeg
 

YamaDooPolCat

Well-known member
SUPER Site Supporter
That reverse seal idea would certainly do the trick when crossing a bit of water. The slightly colder water would usually be quickly pulled into the wheel bearing, but the reverse seal would just tighten up and keep water out.
Good idea for sure!
 

Track Addict

Bronze Member
GOLD Site Supporter
The rear idler helps to break up packed snow in the track. Certain snow conditions can cause a layer build up and the tracks can walk off. The ice breaker wheel prevents that or should anyways.
 

Track Addict

Bronze Member
GOLD Site Supporter
Worked on a few tracks this weekend! Tucker ready for snow if it happens this year.

Amazing what 100 miles north to south does. Watch for train track switches! Wedged this one in. Funny part is I have the kids a talk and instructions on how to avoid this earlier in the day. No damage or injuries.

54317C82-4C1D-4D53-AEDF-F32D684ED359.jpeg
A2588DA0-9BAF-4078-A8E8-B53A89D53F02.jpeg
A1EEDEF2-2E70-4790-A4B5-617B0567E96D.jpeg
B93B4177-D329-4D78-B785-91BA70125750.jpeg
 
Top