Forums Forums - Off Topic Forum FUN




Go Back   Forums Forums - Off Topic Forum FUN > Agriculture & DIY Forums > DIY Forums > DIY Plumbing Forum

Reply
 
Thread Tools Display Modes
  #1  
Old 12-12-2017, 11:29 AM
bczoom bczoom is offline
Super Moderator

 
Join Date: Sep 2005
Posts: 16,428
Thanks: 1,025
Thanked 1,576 Times in 760 Posts
bczoom will become famous soon enoughbczoom will become famous soon enough
Style: T66
Default Need help with plumbing issue

My son was bringing firewood up to the house last night. Got his sweatshirt caught in the ATV throttle while getting off. The ATV took off, sideswiped the house and sheared off the outside water spigot.

There's not enough pipe sticking out to solder or attach a sharkbite around the outside of the pipe.

Looking for ideas/options for connecting a new spigot but need to go inside the existing pipe unless I start tearing out mortar.

Not sure how well I could do a sweat joint since it's embedded in the brick so ideally, I'd like to find a self-tapping or compression fit connector that would go inside the existing pipe.

I checked SharkBite connectors site and I don't see they make something like this.

Ideas?
Attached Images
File Type: jpg IMG_20171212_101501_040.jpg (157.2 KB, 31 views)
__________________
If you didn't hear it with your own ears or see it with your own eyes, don't invent it with your small mind and share it with your big mouth.
Reply With Quote
  #2  
Old 12-12-2017, 11:37 AM
TiredRetired's Avatar
TiredRetired TiredRetired is offline
Resident Prick
 
Join Date: Oct 2011
Location: Green Mountain State
Posts: 10,554
Thanks: 5,346
Thanked 10,289 Times in 3,990 Posts
TiredRetired has a spectacular aura aboutTiredRetired has a spectacular aura about
Default Re: Need help with plumbing issue

I'm not much of a plumber but I'll toss my hat in the ring.

I would go and rent a Hilti or similar electric hammer drill, chisel away the mortar and find good pipe to connect to. I am not familiar with sharkbites so I cannot help in that regard.

If you are going to all that trouble, may as well just cut the pipe all the way back into the basement and install a anti siphon frost free silcock, but what the hell do I know.

After all that, maybe a protective bollard to make is son safe would be in order.
__________________
DIVERSITY IS A CODE WORD FOR WHITE GENOCIDE.
Reply With Quote
The Following User Says Thank You to TiredRetired For This Useful Post:
bczoom  (12-12-2017)
  #3  
Old 12-12-2017, 11:55 AM
bczoom bczoom is offline
Super Moderator

 
Join Date: Sep 2005
Posts: 16,428
Thanks: 1,025
Thanked 1,576 Times in 760 Posts
bczoom will become famous soon enoughbczoom will become famous soon enough
Style: T66
Default Re: Need help with plumbing issue

I'm sort of thinking along the same lines you are if I can't attach something from the outside (which is my hope).
__________________
If you didn't hear it with your own ears or see it with your own eyes, don't invent it with your small mind and share it with your big mouth.
Reply With Quote
  #4  
Old 12-12-2017, 12:40 PM
EastTexFrank's Avatar
EastTexFrank EastTexFrank is offline
Gold Member
 
Join Date: Sep 2005
Location: East Texas
Posts: 9,199
Thanks: 1,066
Thanked 2,818 Times in 1,341 Posts
EastTexFrank will become famous soon enough
Default Re: Need help with plumbing issue

Not sure that I can help you much as I'm not aware of anything that seals inside the existing pipe. All my outside spigots are the freeze free type and the only time that I've had to replace one I had to drill and chisel out the mortar to get it out of the wall. I've used sharkbites but only on PEX, never on copper so I can't vouch for that either.



Let us know what you decide to do as it may be helpful in the future.
__________________
ETF


I won't be wronged. I won't be insulted. I won't be laid a-hand on. I don't do these things to other people, and I require the same from them. John Wayne as JB Books in "The Shootist".
Reply With Quote
The Following User Says Thank You to EastTexFrank For This Useful Post:
bczoom  (12-12-2017)
  #5  
Old 12-12-2017, 12:53 PM
bczoom bczoom is offline
Super Moderator

 
Join Date: Sep 2005
Posts: 16,428
Thanks: 1,025
Thanked 1,576 Times in 760 Posts
bczoom will become famous soon enoughbczoom will become famous soon enough
Style: T66
Default Re: Need help with plumbing issue

I've used the SharkBite's on copper. They work very well.

If I'm pulling out a drill and/or tearing up the interior wall, it'll wait until Spring. It's too damn cold to do it now and the water to that spigot is already shut so it can wait if needed.

If I could just pop something in from the outside, I can do that in the winter.
__________________
If you didn't hear it with your own ears or see it with your own eyes, don't invent it with your small mind and share it with your big mouth.
Reply With Quote
  #6  
Old 12-12-2017, 01:05 PM
EastTexFrank's Avatar
EastTexFrank EastTexFrank is offline
Gold Member
 
Join Date: Sep 2005
Location: East Texas
Posts: 9,199
Thanks: 1,066
Thanked 2,818 Times in 1,341 Posts
EastTexFrank will become famous soon enough
Default Re: Need help with plumbing issue

Not sure that I can help you much as I'm not aware of anything that seals inside the existing pipe. All my outside spigots are the freeze free type and the only time that I've had to replace one I had to drill and chisel out the mortar to get it out of the wall. I've used sharkbites but only on PEX, never on copper so I can't vouch for that either.



Let us know what you decide to do as it may be helpful in the future.

I just had a thought. There is a tool called a tubing or pipe swager. I haven't seen one used in years but it was just a die that was placed inside the pipe and hit with a hammer. They probably have fancier versions by now but it opened the end of the pipe enough to slide another section of pipe in to it. It may not work in your case since the pipe is surrounded by mortar. The internet is your friend.
__________________
ETF


I won't be wronged. I won't be insulted. I won't be laid a-hand on. I don't do these things to other people, and I require the same from them. John Wayne as JB Books in "The Shootist".
Reply With Quote
The Following User Says Thank You to EastTexFrank For This Useful Post:
Doc  (12-12-2017)
  #7  
Old 12-12-2017, 01:10 PM
Doc's Avatar
Doc Doc is offline
Forum Admin

 
Join Date: Sep 2005
Location: Ohio, USA
Posts: 33,261
Thanks: 18,519
Thanked 14,321 Times in 5,668 Posts
Doc will become famous soon enoughDoc will become famous soon enough
Default Re: Need help with plumbing issue

Wow, he really sheared it off. Lucky he didn't get hurt. I agree with the others, I know of no way to fix that other than tearing up the mortar, and if you are doing that you might as well replace it with another anti freeze one. I'm afraid there is no easy fix for this.
__________________
Scott me up Beamy.

Other Fun Forums:

Weekend Mudders + Net Tractor and RTV Talk + Net Cooking Talk
Reply With Quote
  #8  
Old 12-12-2017, 01:31 PM
bczoom bczoom is offline
Super Moderator

 
Join Date: Sep 2005
Posts: 16,428
Thanks: 1,025
Thanked 1,576 Times in 760 Posts
bczoom will become famous soon enoughbczoom will become famous soon enough
Style: T66
Default Re: Need help with plumbing issue

Quote:
Originally Posted by Doc View Post
Lucky he didn't get hurt.
Maybe then, I'd have some pity on him but for now, I'm just pissed.

Besides taking out the spigot, he took off the dryer vent cover and hit an antique marble table. If that table had broke, I'd be seriously pissed. The dryer vent is an easy fix.
__________________
If you didn't hear it with your own ears or see it with your own eyes, don't invent it with your small mind and share it with your big mouth.
Reply With Quote
The Following User Says Thank You to bczoom For This Useful Post:
Doc  (12-12-2017)
  #9  
Old 12-12-2017, 03:09 PM
road squawker's Avatar
road squawker road squawker is offline
Bronze Member
 
Join Date: Feb 2014
Posts: 1,354
Thanks: 1,102
Thanked 1,790 Times in 794 Posts
road squawker is on a distinguished road
Default Re: Need help with plumbing issue

go inside the house and cut off the pipe.
Solder a new smaller pipe to it and run the smaller pipe thru the old one, it's just a hose bib so you really won't notice the slight loss of water volume.

or,...(best solution), knock out the mortar and replace with all new piping.
Reply With Quote
The Following User Says Thank You to road squawker For This Useful Post:
bczoom  (12-12-2017)
  #10  
Old 12-12-2017, 03:48 PM
TiredRetired's Avatar
TiredRetired TiredRetired is offline
Resident Prick
 
Join Date: Oct 2011
Location: Green Mountain State
Posts: 10,554
Thanks: 5,346
Thanked 10,289 Times in 3,990 Posts
TiredRetired has a spectacular aura aboutTiredRetired has a spectacular aura about
Default Re: Need help with plumbing issue

Quote:
Originally Posted by bczoom View Post
Maybe then, I'd have some pity on him but for now, I'm just pissed.

Besides taking out the spigot, he took off the dryer vent cover and hit an antique marble table. If that table had broke, I'd be seriously pissed. The dryer vent is an easy fix.
Well, that idea of a bollard is looking better and better.
__________________
DIVERSITY IS A CODE WORD FOR WHITE GENOCIDE.
Reply With Quote
The Following User Says Thank You to TiredRetired For This Useful Post:
bczoom  (12-12-2017)
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Weird issue with bathroom plumbing jpr62902 DIY Plumbing Forum 6 03-19-2015 12:29 AM
Joe's Affordable Plumbing Act of 2014 Doc Jokes_Forum 5 01-19-2014 02:33 AM
PEX plumbing review BigAl Home Improvement Projects, Appliance upgrades, Misc Household items Forum 9 03-14-2011 10:32 PM
Joe's Fair Plumbing Act PBinWA Jokes_Forum 1 10-30-2008 07:48 PM
Amercan Standard Plumbing issue Junkman Home Improvement Projects, Appliance upgrades, Misc Household items Forum 2 01-11-2008 02:51 PM





All times are GMT -4. The time now is 03:27 AM.


Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright 2002 - 2018 www.ForumsForums.com